Yeah people will give you shit for the TRS-25, but they're absolutely worth the money when you find them on sale. They're normally about $75, and I don't know if there have been deals in the past year, but I got one in 2018 for just $40. But be careful of the seller/retailer, as I've heard of fakes going around.
Put a romeo on the HD rifle and hope shake awake works?
I've had an R5 on my 9mm AR pistol for like 18 months at this point? Every single time I pick up or move the gun (which is about once a week because of reasons), the dot is already on by the time I get my eye lined up to it to check. I've got no qualms at all about relying on it.
Insert pun about anaconda and buns
Here's video of this incident: https://www.youtube.com/watch?v=_TK7Cm6Ydks
And long-term, too. Since they won the MHS program, they're basically locked in with the DoD for the next 20+ years. Fill the initial contract below cost, and fill all the subsequent contracts at a decent profit.
In regards to your stock/brace question, here's how I understand it:
Brace manufacturers have to get an explicit approval from the ATF that their product is a brace and not a stock. Because by default, if it could be used a stock, then it's a stock....until you get that rubber stamp from the ATF. But the approval KAK got from the ATF applies to that specific product, and would not apply to your 3D-printed clone of it, even it was functionally/dimensionally identical.
So yeah, fucking around with that will rile up the fedbois. Either pony up for official braces, pony up for a Form 1 and SBR it, or print away but keep your dog at your neighbor's house.
I know about him, but there were other handgun shots that weren't him -- some of them even after he was already incapacitated.
Nah, 3rd guy was only a knock and got rezzed
He says in one video that he's a trained EMT, and points out his medkit bag (which he still has in this picture, that's the second sling across his chest). If your intent is avoiding prints and residue, you'd use actual tactical gloves or at least some cheap mechanics gloves, not purple latex.
In the full set of videos that include the short pedo that he domed, there's also one handgun shot, then he fires four from his AR, and then there are three more handgun shots -- https://weekendgunnit.win/p/GvP5WKtd/full-video-of-the-kenosha-shooti/c/
No word on who had the handgun or who they were shooting at.
what do I have to say to birth a howitzer
shoot your guns in a residential area
Nope, reusable, unless you're a gorilla and fuck them up. After buying a lower+jig kit, you can buy just 80% lowers from then on.
I don't have any direct experience, but every time I've seen people talk about detachable-mag shotguns, someone always pipes up about bad reliability. And of course magazine cost. And IMO they just don't look good.
If you're just worried about shell quantity, there are always the KSG and DP12, but likewise I don't know anything about their reliability either.
Y'all realize that article and quote is fake, right?
My wife had a guy over at our house literally 3 days after she kicked me out. I only willingly left because it was supposed to be a temporary separation while we went to counseling and worked shit out, so much for that. Fucking state has now been sitting on the divorce papers for 90 days, doing nothing, when they're supposed to be done in 30. The mortgage company won't work on trying to refinance the mortgage until the divorce is final, so they haven't told her yet that she won't qualify for that mortgage on her teacher's salary. Which means she's still in the house and I'm living in my parents basement like a fucking teenager since I got laid off from my job the same week we filed the divorce papers (in May). Feels bad man.
Fuck the feds, fuck bitches, and fuck 2020.
Having to buy a CZ afterwards, in this market, is a downside.
This is why you restrict your hole-drilling to the lower receiver only.
Is the front scope mount taller than the rear? Permanent elevation adjustment?
Creality CR10 S5 is the cheapest one I know of that has a 20 inch (500mm) square print size.
Creality's Ender 3 is considered the best budget printer, so I assume the CR10 S5 is the best budget large format printer.
If you're talking about oil filters though, a 3D printed one won't hold up. They might last a little bit if your oil feed line diameter is 0.22 inches, but anything larger than that is just going to explode.
Correct, he has a film production armorer business (which is why he can have and afford so many full auto guns).
SHORT AND WEAK
You sure are glowing hard with your 3-hour-old account, alphabet boi.